THINGS LOCAL / PRIVATE

BLONDA / MIDI TOOL 012

give the little wheel
a new job.

Choose a MIDI CC and channel. OR.1 creates a tiny SysEx settings file entirely inside this browser.

SAFE PATH CONFIGURATION ONLY · NO FIRMWARE PATCH · NO UPLOAD

BUILD SEQUENCE4 STEPS
  1. 01
    MAPchoose the job
  2. 02
    VERIFYinspect the bytes
  3. 03
    DOWNLOADsave a .syx file
  4. 04
    SENDoptional Web MIDI
PRIVACY
LOCAL ONLY
OUTPUT
SYSEX / .SYX
DEVICE
OR-1
FIRMWARE
UNCHANGED
DEVICE / ORTHO REMOTECONFIG PREVIEW
01 / TURN THE WHEEL
VALUE PREVIEW / 000—127
ORTHO REMOTE / OR.1
TEST VALUE064
FILTER CUTOFFCC 32 · CH 1 · VAL 064
FORMAT VERIFIED AGAINST TE OR-1 SYSEX SPEC OFFICIAL SOURCE ↗
BASE OR-1MODE LOCAL READY

OR.1 / TE DEVICE LIBRARY / CONTROL MAPPER

one wheel.
any CC.

Nothing from pkg_v2_3_3 is needed or uploaded. This writes only the OR-1 settings described by the manufacturer.

01TARGET DEVICE / ROTARY DESTINATION
OP-XY / OFFICIAL + TESTED— MAPPINGS
OFFICIAL MIDI SOURCE ↗

Only documented mappings are named. A manual CC remains available for everything else.

CCPARAMETERCHANNELRANGE

02ENCODER BEHAVIOUR
03VERIFIED OUTPUT
TARGETOP-XY / FILTER CUTOFF
CC032
CHANNEL01
MODEABSOLUTE
SYSEX MESSAGE11 BYTES
F0 00 20 76 02 00 00 00 20 01 F7
blonda-or1-cc032-ch01-abs.syxNO UPLOAD · NO FIRMWARE
04DIRECT SEND / WEB MIDI
OPTIONAL

find OR.1 and send.

The browser can list MIDI outputs already visible to your operating system. Pair OR.1 as BLE-MIDI first, then choose it here. The page cannot scan unpaired Bluetooth devices.

CHECKING BROWSERNOT CONNECTED · DOWNLOAD STILL WORKS

CHECK THE DESTINATION. This sends only the small settings message shown above. Send it to OR.1, never to OP-XY or another instrument.

LOAD / TEST / TROUBLESHOOTREAD BEFORE SENDING
01

connect as BLE-MIDI.

On macOS, open Audio MIDI Setup → MIDI Studio → Bluetooth Configuration. Put OR-1 in pairing mode and press Connect.

02

send it one of two ways.

Use the Web MIDI panel above in a supported browser, or open SysEx Librarian and send the downloaded file to OR-1 — never to OP-XY.

03

let OP-XY receive it.

On OP-XY: COM → M3 (Devices) → your controller. Set the MIDI filters to IN. OTHER is the filter that passes MIDI CC.

04

test the simple thing first.

Try CC 7 first. If OP-XY volume moves, the connection works. Then load CC 32 for filter cutoff or CC 33 for resonance.

IMPORTANT

This tool creates a settings message, not firmware. Do not install unknown or untested firmware over wireless DFU. A bad firmware change can make OR-1 unusable; keep a physical recovery route before experimenting.

DIAGNOSTIC

ask OR-1 for its current settings.

This official-format read request does not change a setting. Its response still requires a SysEx monitor to inspect.

OFFICIAL REFERENCESOR-1 GUIDE ↗OP-XY COM ↗WEB MIDI SUPPORT ↗
01 / PRIVATE

The configuration is generated in your browser. No file or setting is sent to BLONDA.

02 / MINIMAL

With button settings off, the file changes only channel, rotary CC and absolute/relative mode.

03 / INDEPENDENT

BLONDA is not affiliated with or endorsed by Teenage Engineering. OR-1 and OP-XY identify the target devices.